Speedy Air Power Draw Bar
Speedy Power Drawbar - Authorized Distributor - Proudly Made in the USA

Call Toll Free @ 800-575-2843 || Back to Air Power Draw Bars || Speedy Air Power Site

Built for Speed and High Efficiency

The Finest Air Powered Drawbar in the Industry

Speedy Air Power Draw Bar is a Pneumatic Air Powered Auto Drawbar That Fits Manual Mills/Milling Machines

SERVO POWER DRAWBAR
For Variable Speed and Step Pulley Type Milling Machines

 Speedy Air Power Draw Bar

Our Drawbars Come Complete with regulator, gauge, filter, lubricator, drawbar, mounting hardware, operators manual, and parts lists

  • Super Fast Four second tool change
  • Easy installation and operation, no special tools needed
  • Push button control
  • Uses standard shop air supply
  • Eliminates excessive downtime
  • Increases productivity
  • Ends collet sticking
  • No special collets or tool holders needed
  • Provides uniform tightening of collets
  • Four second tool change
  • Easy installation and operation, no special tools needed
  • Deluxe Push button ON/OFF control unit
  • Uses standard shop air supply PSI
  • Eliminates excessive downtime
  • Reduces Operator Collet Changing Fatigue
  • Maximizes Shop Effiency plus Increases productivity
  • Ends collet sticking and helps prolong Collet or Toolholder life
  • No special collets or tool holders needed
  • Provides uniform tightening of collets
  • Factory Supported Limited Warranty

COMPARE OUR 100% USA MADE with Our Superior Quality, performance, manufacturing features and LOW COST!

The Speedy Air Power Draw Bar is Factory Designed to only take a few minutes to install and learn to operate. It's fast and easy. No special tool are required to install this power drawbar. It come complete with a limited warranty and is proudly made in the USA!

 Speedy Air Power Draw Bar

Note: When placing your order for the Speedy Air Power Draw Bar , please be sure to specify the make and model of your milling machine R8 spindle, or select 30 or 40 tapered collet.

Reasons to Buy and Use Speedy Air Power Draw Bar:

Servo 140 Series Power Feed

  • Semi-automated machining on Class 1 mills to 3 hp.
  • Peak Torque (half-wave series motor): to 140 in-lb/15.8 N-m.
  • Intermittent Torque: 105 in-lb/11.9 N-m.
  • Continuous Torque: 90 in-lb/10.2 N-m
  • Variable Feed Rate: .75-25 ipm or 19-635mm/min. (table/cross); 0-12 ipm or 0-305mm/min. (knee).
  • Rapid Traverse: 35 ipm or 889 mm/min. (table/cross); 12 ipm or 305 mm/min. (knee).
  • Gear Reduction Ratio (motor to lead screw shaft): 72:1.
  • Helical gearing and torque limiting friction safety clutch.
  • Electrical: 110V, 50/60 Hz, 2.5A.
  • Approx. weight: 15 lb./6.8 kg.

Servo 150 Series Power Feed

  • Semi-automated (full-wave SCR control compound DC motor): to 150 in-lb/17 N-m.
  • Peak Torque (half-wave series motor): to 140 in-lb/15.8 N-m.
  • Intermittent Torque: 120 in-lb/13.6 N-m.
  • Continuous Torque: 100 in-lb/11.3 N-m.
  • Variable Feed Rate: 50-35 ipm/13-889 mm/min.
  • Rapid Traverse: 35 ipm/889 mm/min.
  • Gear Reduction Ratio 72:1.
  • Helical gearing and torque limiting friction safety clutch.
  • Smooth surface finish at speeds as low as .5 ipm or 13 mm/min. at full torque.
  • Electrical: 110V, 50/60 Hz, 3A.
  • Approx. weight: 15 lb./6.8 kg.
  • Superior speed regulation: ramping, dynamic breaking, friction safety clutch and limiting circuit protection.
Servo 150 Series Power Feed